Beijing Boyuan Jiaheng Environmental Protection Technology Co

Product structure of water softener
The imported control valve body is made of high-strength, lightweight, corrosion-resistant engineering plastics and lead-free brass.
Anti-corrosion tank The material of the tank is fiberglass (carbon steel or stainless steel can be used as a plastic-lined tank. The tank is anti-corrosion and pressure-resistant and has a long service life.
The uniform water distribution system adopts jet water distribution, resin The effective exchange capacity is fully exerted, and the salt control is precise without the need for a salt pump.
The imported high-performance resin uses strong acidic cation exchange resin, with low breakage rate, uniform particle size, and improved ion exchange rate.
Features of water softener device
The overall design of the high-efficiency softened water device is reasonable, so that the effective working exchange capacity of the resin can be fully utilized.
It saves labor and has a high degree of automation, and does not need to have a dedicated person on duty.
Water-saving softened water device produces water The rate reaches above.
The power saving adopts the siphon regeneration principle, no salt pump is needed, and the power consumption is only equivalent to that of manual water softening equipment.
The small space required only requires the space required for a resin tank and a salt tank. , saving the space occupied by the pipeline salt pump.
Easy to adjust. Users can adjust the regeneration cycle and regeneration time according to actual needs.
Low operating costs. Due to the high degree of automation, the water softener can adapt to changes in water volume and accurately Measuring the amount of water production and the amount of regeneration agent accurately avoids the innocent waste of regeneration agent during regeneration, and at the same time saves a lot of labor costs.
Working procedures of water softening device
The untreated water in the water supply passes through the resin layer, causing Reaction produces soft water.
Backwash water enters from the lower part of the resin layer to loosen the resin and remove fine debris.
Incoming brine regeneration uses higher concentration brine to flow through the resin to reduce the expired resin to sodium type resin.
Rinse according to the process of water supply, so that the water passes through the resin to flush out excess salt solution and regenerate the exchanged calcium and magnesium ions.
Water injection Inject water into the salt box to dissolve the salt for next time Used for regeneration.
Technical indicators of water softening device
Working pressure raw water hardness/output water hardness
Working temperature ℃℃ Power supply
Water softening device installation requirements
The foundation must be level and set up nearby Floor drains or drainage ditches to drain away regeneration wastewater. An independent power socket should be provided near the equipment.
The salt box should be close to the exchange tank, and the salt suction pipe should be as short as possible.
An upper molding should be installed on the water inlet pipe. Filters, water meters, and water outlets should be equipped with sampling ports.
Manual valves should be installed on the water inlet and outlet pipes, and bypass valves should be installed between the water inlet and outlet to continue supplying water during regeneration or maintenance.
Water inlet port If the pressure is lower than that, an automatic booster water pump needs to be added.
The salt in the salt box must be industrial salt, and iodized salt and calcium salt cannot be added. In order to ensure that the concentration of the salt solution in the salt box can reach saturation, the dissolution time should first be guaranteed It should not be less than an hour, and it should be forced to regenerate once before the first use.
When the raw water hardness is /H, the larger grade should be selected.
The pipeline must be flushed before use to avoid impurities clogging the valve body and contaminating the resin.
Antifreeze measures should be taken in winter in the north.
Water softener control valve model
Time control sets the regeneration cycle based on hourly output and periodic water production, and is generally suitable for situations where water consumption is relatively stable.
The flow control starts the regeneration program based on the periodic water production volume. When the equipment is running, a special flow meter counts the total water production. When the total water production reaches the set periodic water production volume, the controller starts the regeneration program for automatic regeneration. The regeneration of the equipment has nothing to do with the running time, and is generally suitable for situations with unstable water consumption and continuous water use.
Parameters required for user selection
Water production per hour (unit
Source of raw water and its total hardness, total alkalinity, total salt content
Effluent hardness requirements (unit
Water inlet pressure (unit, best between
Daily water consumption
Company official website
Company address Jiugong No., Daxing District, Beijing
Contact person Manager Chang
Contact Telephone
Landline