Beijing Boyuan Jiaheng Environmental Protection Technology Co

Generally speaking, the operation of boiler softened water equipment must go through five processes of product water backwashing, regeneration, slow flushing and fast flushing. All processes of different types of equipment are very close, but there may be some additional processes due to differences in actual processes or control needs. Any softened water equipment based on sodium ion exchange is developed on the basis of these five processes.

Since solid granular table salt contains a certain amount of impurities, a large amount of impurities will be deposited at the bottom of the salt tank and block the salt valve, so the impurities at the bottom of the salt tank must be cleaned regularly. When cleaning, you can open the drain valve at the bottom of the salt box and rinse it with clean water until no impurities flow out. The cleaning cycle of the salt box should be determined based on the impurity content of the solid granular salt.

Two main technical indicators:
Raw water supply pressure< b >
~
Raw water hardness< b >
/ (calculated as /+/+)
Dissolved solids< b >
/
Outlet water hardness< b >
/ (calculated as /+/+)
Raw water temperature< b >
~℃
Ambient water temperature< b >
~℃
Water production volume< b >
︿/
Resin tank (model)< b >
~< br/> Resin quantity< b >
~
Salt bucket volume< b >
~
Regeneration salt< b >
Large grains, iodine cannot be added, add calcium salt.
Three equipment features:
◇High degree of automation, the boiler softened water equipment automatically completes the softening and regeneration cycle processes according to the preset program. Daily operation requires no manual operation except adding salt.
◇It occupies a small area, the equipment has a compact structure, is compact and lightweight.
◇ Strong corrosion resistance, the tank is made of fiberglass, engineering plastics or stainless steel to avoid corrosion of the equipment by the regenerant.
◇Reliable performance and stable water quality.
◇Flexible selection, single tank, double tank, multi-tank system time flow control mode, simultaneous regeneration, alternate regeneration and other operating modes can be selected according to needs.
Four specifications model
Model< b >
Water production volume/< b >
Resin tank size< b >
Resin volume< b >
Salt barrel
< b >
< b >
< b >
< b >
< b >
< b >
< b > < br/>< b >
< b >
~< b >
< b >
< b >
(points)< b >
~ < b >
< b >
< b >
(inch)< b >
~< b >
< b >
< b > < br/> High< b >
~< b >
< b >
< b >
< b >
~< b >
< b >
< b >
High< b >
~< b >
< b >
< b >
< b >
~ < b >
< b >
< b >
High< b >
~< b >
< b >
< b >
< b >
~< b >
< b >
< b >
High< b >
~< b >
< b > < br/>< b >
< b >
~< b >
< b >
< b >
High< b >
~< b >
< b >
< b >
< b >
~< b >
< b >
< b >
High< b >
~< b >
< b >
< b >
< b >
~< b >
< b >
< b >
< b >
~< b >
< b >
< b >
< b >
~< b >
< b >
< b >

What you need to know about five types of selection
Water consumption per hour (unit)
Raw water hardness (unit) (based on water quality inspection report Subject to)
Potassium and sodium content of raw water (unit: (subject to water quality inspection report)
Outlet water hardness requirements (unit
Working pressure (unit: (, the best is
continuous Water supply time (unit: )
Ambient temperature and raw water temperature (unit: ℃)
Six installation requirements
There is no need to specialize in the installation foundation, the foundation level can be
If the inlet water pressure is low , a pipeline pump must be installed.
The pipeline must be flushed before use to avoid impurities clogging the valve body and contaminating the resin.
Do not use iodized salt or calcium salt as a regeneration agent. Add salt to the salt tank regularly to ensure the saturated concentration of the salt water (the dissolution time should be guaranteed to be no less than six hours).
Seven Equipment Post-Maintenance
Regularly check the air tightness of the boiler softened water equipment ejector and salt absorption pipeline to prevent air leakage and affect the regeneration effect. The water softener should be disassembled once a year, the impurities in the upper and lower water distributors and quartz sand cushion should be cleaned, and the loss and exchange capacity of the resin should be checked. Seriously aged resin should be replaced. Resins with iron poisoning can be resuscitated with solutions.

Ensure that the input voltage and current of the boiler softened water equipment are stable and prevent the electronic control device from burning out. A sealing cover should be installed outside the electronic control device to prevent moisture and flooding. Add solid granular salt to the salt box regularly, and ensure that the salt solution in the salt box is in a supersaturated state. When adding salt, be careful not to sprinkle solid granular salt into the salt well to prevent salt bridges from forming on the salt valve and blocking the salt suction pipeline.

Company official website:
Company address: Jiugong No., Daxing District, Beijing
Contact person: Manager Chang
Contact number:
Landline